상품 수정
신규저장
저장후 돌아오기
상품분류 정보
1단계분류
2단계분류
3단계분류
4단계분류
5단계분류
상품분류 내 계속등록
상품기본정보
제품코드
제품명(국문)
오메가 T-BAR 25mm, 35mm
제품명(영문)
OMEGA T-BAR 25mm, 35mm
검색어
AL 오메가 T-BAR 25mm,35mm,AL OMEGA T-BAR 25mm
제품의 소개(국문)
오메가 T-BAR SYSTEM은 바에 홈을 넣어 벽 칸막이의 상부 러너를 이 홈을 이용 고정하게하는 기능을 갖어 미적감각과 실용성을 동시에 살린 천장시스템으로 시공이 매우 간편하고, 빠르며, 설치된 전 구간에서 점검구 역할이 가능하여 배선이나 배관 등의 보수점검이 용이합니다. BAR에 홈이 있어 그홈을 살린 디자인이 가능하여 일반사무실, 상가 등 건축물 내부의 모든부위에 적합한 시스템입니다.
제품의 소개(영문)
OMEGA T-BAR system has groove in its bar and by putting upper runner of wall partition into such groove such partition cab be fixed. Thus it is aesthetically beautiful and practical and as ceiling system its work is very simple and quick. At whole sector of its installation it can play role of checking hole and also repair and checking of wiring or pipe laying are simple. There are grooves at its bar accordingly design for highlighting such grooves is possible and it is suitable to all parts of inside of building structure such as general office and shopping malls etc.
제품진열여부
사용중
사용안함
제품카다로그
파일업로드
삭제
보기
제품이미지
리스트 이미지
삭제
원본 이미지
제품개요(국문)
제품개요(영문)
제품도면(국문)
제품도면(영문)
시공안내(국문)
시공안내(영문)
기타사항(국문)
기타사항(영문)
제목
내용
삭제
<p>(1) 용어정의 <br> ① 시스템 : AL Ω T-BAR SYSTEM <br> ② 공 법 : LAY-IN(천장틀에 천장마감 판넬을 올려놓는 TYPE) <br>(2) 운송 및 취급<br> ① 운 송 : 종류 및 호칭, 치수, 제조일자등을 라벨에 명기하여 포장후 운반 <br> ② 취 급 : 생산자의 지시사항과 사용자의 유의사항에 따라 취급</p>
제목
내용
삭제
<p>(1) 재료<br> ① 색 상 : 백색(표준색상), 외 주문색상 <br>(2) 규격<br> ① AL Ω MAIN T-BAR : 25mm X 38mm X 1.2T (일반용 L=3600)<br> ② AL Ω CROSS T-BAR : 25mm X 38mm X 1.2T (일반용 L=600)<br> ③ HANGER BOLT : ψ9mm <br> ④ HANGER & PIN : 105mm X 20mm X 2.0T <br> ⑤ CARRYING CHANNEL : 38mm X 12 mm X 1.2T <br> ⑥ C/C JOINT : 100mm X 35mm X 10 mm X1.2T<br> ⑦ C/T CLIP (AL Ω T-BAR용) <br> ⑧ MINOR CHANNEL : 19mm X 10mm X 1.2T <br> ⑨ M/C CLIP : 38mm X 14mm X 1.2T<br> ⑩ HANGER NUT : ψ9mm<br> ⑪ MOLDING (AL Ω T-BAR용)<br> ⑫ ANGLE MOLDING : 22mm X 32mm X 0.5T<br> ⑬ DOUBLE MOLDING : 15mm X 10mm X 15mm X 24mm X 0.5T</p>
제목
내용
삭제
<p>* 시공이 빠르고 간편하다.<br>* 천장판 어디나 점검구 역할이 가능하다,<br>* 바의 폭이 좁아 미려하다.<br>* 격자무늬의 천장을 연출하여 단조로움을 없애 준다.<br>* 상부러너를 바의 홈에 장착하여 실용적이다.</p>
제목+내용 1줄 추가
제목
내용
삭제
<br><h3>(1) Definition of terms</h3><ul><li>① System: AL Ω T-BAR SYSTEM</li><li>② Method; Lay-in (A type whereby ceiling finishing panel is placed on ceiling frame)</li></ul><h3>(2) Transportation and handling</h3><ul><li>① Transportation: Transport after recording type, name, dimension and manufacturing date etc. on the label and then packing.</li><li>② Handling: Handle it according to instruction of manufacturer and requirement of the user.</li></ul>
제목
내용
삭제
<br><h3>(1) Material</h3><ul><li>① Color : white (standard color) and order color</li></ul><h3>(2) Dimension</h3><ul><li>① AL Ω MAIN T-BAR (25 mm x 38mm x 1.2T (for general purpose L=3600)</li><li>② AL Ω CROSS T-BAR 25 mm x 38mm x 1.2T (for general purpose L=600)</li><li>③ HANGER BOLT : ψ9mm </li><li>④ HANGER & PIN : 105mm X 20mm X 2.0T </li><li>⑤ CARRYING CHANNEL : 38mm X 12 mm X 1.2T </li><li>⑥ C/C JOINT : 100mm X 35mm X 10 mm X1.2T</li><li>⑦ C/T CLIP (for AL Ω T-bar)</li><li>⑧ MINOR CHANNEL : 19mm X 10mm X 1.2T </li><li>⑨ M/C CLIP : 38mm X 14mm X 1.2T</li><li>⑩ HANGER NUT : ψ9mm</li><li>⑪ MOLDING (for AL Ω T-bar)</li><li>⑫ ANGLE MOLDING : 22mm X 32mm X 0.5T</li><li>⑬ DOUBLE MOLDING : 15mm X 10mm X 15mm X 24mm X 0.5T</li></ul>
제목
내용
삭제
<ul><li>* Working is fast and simple.</li><li>* Any ceiling plate can play role for checking hole.</li><li>* Width of bar is narrow so it is beautiful.</li><li>* Removes sense of monotony by presenting cross stripes ceiling.</li><li>* By mounting upper part runner to groove it is practical.</li></ul>
제목+내용 1줄 추가
제목
내용
삭제
<img src="/html/yoochang/image/nav_sub/contents//product6.gif" alt="">
제목+내용 1줄 추가
제목
내용
삭제
<img src="/html/yoochang/image/nav_sub/contents//product6.gif" alt="">
제목+내용 1줄 추가
제목
내용
삭제
<p>(1) 건물 중심선 설정 : 천장면의 정밀한 실측 후에 등라인, 디퓨져위치 등 타공정을<br> CHECK하여 중심선을 설정한다.<br>(2) 스트롱 앙카 작업<br> ① 스트롱 앙카 작업시 : 중심선이 설정되면 스트롱 앙카(ψ9mm) 고정부위를 슬라브 <br> 표면에 표시한 후 드릴로 뚫고 고정한다.<br> ② 주물 인서트 작업시 : 도면에 따라 주물 인서트(ψ9mm)를 거푸집에 설치한다.<br> ③ 유의사항 : 앙카 또는 인서트간의 간격과 직각에 유의한다.<br> ④ 스트롱 앙카 또는 인서트는 캐링 채널의 설치 방향을 고려하여 설치 간격을 <br> @900∼1,200mm로 하는 것이 이상적이다.<br>(3) MOLDING LINE LEVEL CHECK<br> ① 물 수평 방법이나 LEVEL기 사용 <br> 가. 도면에 의한 위치 확정(천장 높이 확정) <br> 나. 물 수평에 의한 지점 확인 및 지점과 지점사이 먹 메김.<br> ② 유의사항 : 물 수평 사용할 때 호스내의 기포 유무 확인 및 호스의 파손여부 확인후<br> LEVEL CHECK<br>(4) 벽 몰딩 부착 (앵글 또는 갈매기 몰딩을 도장하여 사용)<br> ① 먹줄에 따라 몰딩을 부착하며 벽 몰딩은 1" 콘크리트 못을 사용하여<br> 고정한다. (간격 500∼1,000mm) ?<br> ② 몰딩과 몰딩 사이의 높이 및 간격이 이완되지 않도록 유의해야 한다.<br> ③ CURTAIN BOX등 시설물과 관련하여 사양에 따라 부착한다.<br><br>(5) 행어 볼트 설치<br> ① 행어 볼트 상부를 스트롱 앙카 또는 인서트에 고정시키고 볼트하부는 마감천장<br> 높이를 고려하여 행어 및 너트로 고정한다.<br> ② 설비 닥트 및 기타 장애물이 있는 곳은 도면 사양에 따라 보강한 후 작업한다.<br> (6) 등라인 설치 ?<br> 등라인 설정 사양에 따라하되 전기 및 설비 관계자와 협의 요함.<br> (7) 캐링 채널 설치<br> 행어 세트와 캐링 채널을 결착 후 고정시키며 @900∼1,200mm 간격으로 설치한다.<br> 캐링 채널의 연결 부분은 CARRYING JOINT를 사용하여 연결한다.<br> 또, 캐링 채널은 벽 또는 커텐 박스 면에서 30cm이상 떨어지지 않도록 설치한다.<br> (8) 마이너채널 설치<br> 시공 면적이 넓은 경우 설치된 캐링 채널위에 보강채널(마이너채널)로 보강고정 시키며<br> @2,000∼3,000mm 간격으로 설치한다.<br> (9) MAIN 및 CROSS AL Ω T-BAR 설치<br> ① 시공 중심선에 실을 띄운 후 MAIN AL Ω T-BAR를 제품의 규격 및 등라인에<br> 맞춰 캐링 채널에 직각 방향으로 C/T CLIP을 사용하여 견고하게 설치한다.<br> ② 설치간격 : 일반T-BAR용은 @600mm간격으로<br> 지바트용은 @600mm간격으로 설치한다. ?<br> ③ MAIN AL Ω T-BAR의 홀에 CROSS AL Ω T-BAR TIP을 끼워 설치한다.<br> (홀간격 : 일반용은 @152.4mm이고 지바트용은 @150mm이다.)<br> ④ CROSS AL Ω T-BAR의 설치시 MAIN AL Ω T-BAR의 홀이 다른 MAIN AL Ω<br> T-BAR의 홀과 일치되어야 한다.<br> (10) 마감판 (흡음텍스 / 지바트) 설치<br> ① 설치된 천장틀의 수평을 물 수평 또는 LEVEL기를 사용하여 행어 볼트의 너트로<br> 정확히 맞춘다.<br> ② MAIN 및 CROSS AL Ω T-BAR를 설치 완료한 후 흡음텍스 또는 지바트를 그위에<br> 얹는다. (흡음텍스의 경우 HOLD DOWN CLIP으로 마감판을 고정시킨다.)<br> ③ 흠집, 모서리 파손, 더러움 등의 손상된 마감판 사용을 금지한다.<br> (11) CURTAIN BOX 설치<br> ① 사양에 따라 용도에 적합한 제품을 제작설치 (별도 도장) ?<br> ② 용접 작업이 병행되므로 안전하고 편한 자세로 작업할 수 있도록 작업대를 설치한다</p>
제목+내용 1줄 추가
제목
내용
삭제
<h3>(1) Setting centerline of building: After accurate measurement of ceiling surface set up centerline after checking other work schedule such as lightline and position of diffuser etc.</h3><ul></ul><h3>(2) Strong anchor work</h3><ul><li>① At the time of strong anchor work when centerline is set up mark part for fixing strong anchor (Ф9mm) at slab surface and punch hole with drill and fix it.</li><li>② At the time of work for cash iron insert (Ф9 mm) install it at form according to drawing.</li><li>③ Caution: Pay attention to intervals between anchor and insert and right angle.</li><li>④ It is ideal to make interval for installation as @900∼ 1,200 mm for strong anchor or insert in consideration of direction of installation of carrying channel.</li></ul><h3>(3) Molding line level check</h3><ul><li>① Use of water level or level</li><li>? ?a. Confirming position by means of drawing (confirming height of ceiling)</li><li>? ?b. Confirming the position by water level and ink pot string marking between positions.</li><li>② Caution: At the time of using water check make sure to check level after checking any presence of air bubble in hose and breaking of hose.</li></ul><h3>(4) Attachment of wall molding (using after painting angle or sea gull molding)</h3><ul><li>① Attach molding along the India ink line and fix wall molding by using 1" concrete nail. (interval 500∼ 1,000 mm)</li><li>② Be careful not to slacken the height and interval between moldings.</li><li>③ In connection with facilities such as curtain box it shall be attached according to specification.</li></ul><h3>(5) Installation of hanger bolt</h3><ul><li>① Upper part of hanger bolt is fixed to strong anchor or insert and power part of bolt is fixed with hanger and nut in consideration of ceiling height at finishing.</li><li>② At the place where installation duct or other obstacles are present work shall be carried out after reinforcing it according to specification.</li></ul><h3>(6) Installation of lightline</h3><ul><li>Install lightline according to specification but it is required to have consultation with persons in charge of electricity and facility.</li></ul><h3>(7) Installation of carrying channel</h3><ul><li>After linking hanger set and carrying channel fix it and install it with an interval of @900∼1,200 mm. The joint part of carrying channel shall be connected by using carrying joint.</li><li>At the time of installing carrying channel make sure to install it not to be off from wall or curtain box surface more than 30 cm.</li></ul><h3>(8) Installation of minor channel</h3><ul><li>When area for works is broad reinforce and fix with supplementary channel (minor channel) installed above the carrying channel and install it with an interval of @2,000∼3,000 mm.</li></ul><h3>(9) Installation of Main and Cross AL Ω T-bar</h3><ul><li>① Install Main AL Ω T-bar sturdily by using C/T cup toward right angle direction to carrying channel according to dimension of the product and lightline.</li><li>② Intervals for installation: for general T-bar interval is @610 mm and for Zierbart interval for installation is @600 mm.</li><li>③ It is installed by inserting CROSS Ω T-Bar Tip to hole of Main AL Ω T-bar.(Interval of hole: for general use it is @152.4 mm and for Ziebart it is @150 mm.)</li><li>④ At the time of installation of CROSS AL Ω T-Bar hole of MAIN AL Ω T-BAR shall match to hole of another MAIN AL Ω T-BAR.</li></ul><h3>(10) Installation of finishing plate (sound absorption tex/ Ziebart)</h3><ul><li>① Accurately set level of installed ceiling frame by bolt and nut through using water level or level.</li><li>② Place sound absorption tex or Ziebart on Main and Cross AL Ω T-bar after its installation. (In case of sound absorption tex fix finishing plate with hold down clip.)</li><li>③ Prohibit use of finishing plate with scratch, broken corner or dirtied.</li></ul><h3>(11) Installation of curtain box</h3><ul><li>① Manufacturing and installing products suitable to use according to specification (separate painting)</li><li>② Welding work is carried out concurrently therefore install work bench to enable safety in work and working in comfortable stance.</li></ul>
제목+내용 1줄 추가
제목
내용
삭제
<br>
제목+내용 1줄 추가
제목
내용
삭제
<br>
제목+내용 1줄 추가